View TDA21201_239354.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Preliminary Data Sheet
TDA21201
Integrated Switch
(MOSFET Driver and MOSFETs) Features * * * * * * * * * * * *
*
Replaces with one part only the semiconductors of a DC/DC power stage for a 12 V a 1 ... 3.3 V conversion: FET driver + High side FET + Low side FET Raises the efficiency by reducing static and dynamic losses beyond 85 % due to optimized MOSFETs and Driver Reduces overall part count and board space consumption Simplifies and shortens the circuit design and the layout Eliminates the need for external bootstrap components Provides simplest overall output current scalability Protects the Driver and the MOSFETs against overtemperature and shoot-through problems Vcc a Gnd Achieves the lowest thermal resistance Rthjc and Rthja Uses the well-known, easy-to-assemble and robust standard TO-220 and TO-263 (DPak) package Requires no separate supply voltage to operate except 12 V Three state input to enable a shut down mode to turn off both MOSFETs Compatible with standard 2-, 3-, 4-, 6-phase PWM controller ICs Ideal for compact, highly-efficient, multi-phase voltage regulators on motherboards and VRMs Package TO-220-7-3 TO-220-7-230 TO-263-7-2 Marking 21201P7 21201S7 21201B7 Ordering Code Q67042-S4100 Q67042-S4101 Q67042-S4099
P-TO220-7-3
P-TO220-7-230
1
P-TO263-7-2
7
Type TDA21201-P7 TDA21201-S7 TDA21201-B7
Pin Configuration and Function Pin number 1,2,3 4/tab 5 6,7 Pin name GND VOUT IN VCC Pin description Ground Output voltage from common node of the MOSFETs Input signal from PWM controller Supply voltage to MOSFETs and Driver IC
General Description The Integrated Switch TDA21201 incorporates an intelligent MOSFET driver and two Power MOSFETs in a single package to form a fully integrated and optimized power stage of a DC/DC synchronous buck converter including the bootstrap components for the high-side MOSFET. The Power MOSFETs are optimized for lowest static and dynamic losses for a 12 V to sub-3.5 V conversion and can handle up to 30 A output current. The TDA21201 is manufactured in Infineons state-of-the-art multi-chip assembly using a low-Rth 7-Pin
Page 1 Apr-29, 2002
Preliminary Data Sheet
TDA21201
TO-220 package or its associated SMD counterpart TO-263 and Infineons latest chip technologies. Block Diagram
VCC = 12 V (Pin 6-7)
High side FET
VIN to PWM IC (Pin 5)
FET Drive Circuitry
VOUT to output inductor (Pin 4/tab) Low side FET
GND
(Pin 1-3)
Absolute Maximum Ratings
At Tj = 25 C, unless otherwise specified
Parameter Peak voltage supplied to `VCC' pins Peak voltage supplied to `IN' pin, DIN_Peak < 10 % Peak voltage at `Vout' pin to GND Maximum DC output current, VCC = 12 V, VOUT 3.3 V Junction temperature Storage temperature Lead temperature TO-263; MSL1, IPC/JEDEC J-STD-020A Lead temperature TO-220 (soldering, 10 seconds) ESD rating (Human body model) IEC climatic category; DIN EN 60068-1
Symbol VCC_PEAK VIN VOUT_PK IOUT_MAX TJ TS TL TL ESD
Unit Value Min. Max. -5 -5 -10 -55 20* 10 20* 30 150 150 225 260 2k 55/150/56 V V A
C
* The positive peak voltage (= the voltage overshoot during switching transients) at the VCC pins and the OUT pin/tab is limited by the Integrated Switch itself (pls., see the "Over-voltage protection of VCC" paragraph
Thermal Characteristic Parameter Thermal resistance, junctions-case Thermal resistance, junctions-ambient, leaded
Page 2
Symbol
Values Unit Min. Typ. Max. 1.9 K/W 62.5
Apr-29, 2002
Preliminary Data Sheet
TDA21201
SMD version, device on PCB: @ min. footprint @ 6 cm cooling area Electrical Characteristics
At Tj = 25 C, unless otherwise specified
62 40
Parameter
Symbol
Conditions
Unit Values Min. Typ. Max. 1.2 0.8 10 -10 -2 20 -10 35 1.6 2.5 22 10 -50 80 A V s mA
Input Characteristic (= MOSFET Driver) Shut down window VIN_SHUT t_SHUT > 1.5 s Shut down hold-off t_SHUT 1.2 V VIN 1.6 V time Supply current during ICC_SHUT 1.2 V VIN 1.6 V shut down VCC = 12 V Current into `IN' pin, IIN_SHUT VIN = 1.4 V during shut down Current into `IN' pin, IIN_LOW VIN = 0.4 V Low Current into `IN' pin, IIN_HIGH VIN = 4.5 V High Static Characteristic (= High Side and Low Side MOSFET) VDS_HS D-S Breakdown Voltage High Side 1.2 V VIN 1.6 V VDS_LS D-S Breakdown ID = 0.25 A Voltage Low Side D-S Leakage Current IDSS_HS High Side 1.2 V VIN 1.6 V D-S Leakage Current IDSS_LS VCC = 12 V High Side Drain-Source on RDSon_HS Resistance High Side IOUT = 15 A Tj = 25 C Drain-Source on RDSon_LS Resistance Low Side Drain-Source on RDSon_HS Resistance High Side IOUT = 15 A Tj = 125 C Drain-Source on RDSon_LS Resistance Low Side Dynamic Characteristic (= Integrated Switch) IN to OUT delay time td(ON) L a H; 50 % to 50 % IOUT = 15 A IN to OUT delay time td(OFF) H a L; 50 % to 50 % (s. Timing Diagram) OUT rise time; 20 % tr to 80 % OUT fall time; 80 to tf 20 %
1.5 16
30
V
0.1
1
A
13.3 4.8 m 17.7 6.4
110 70 10 10
150 100 ns 25 30
Page 3
Apr-29, 2002
Preliminary Data Sheet
TDA21201
Operating Conditions
At Tj = 25 C, unless otherwise specified
Parameter Voltage supplied to `VCC' pins Voltage `IN' Low Voltage `IN' High Input signal transition frequency Pulse width Input Power dissipation Junction temperature
Symbol VCC VIN_L VIN_H f tP_IN PTOT TJ
Conditions
Unit Values Min. Typ. Max. 9 -0.5 2.1 100 90 -25 10 125 15 V 0.8 5.5 500
KHz ns W C
Timing Diagram
50%
VIN
50%
VOUT td(on) td(off)
Typical application A circuit designer will value the Integrated Switch TDA21201 as cost-optimized power stage solution in high-density DC/DC conversion applications using a Vcc = 12 V input where efficiency and board space is an issue, e.g. in multi-phase microprocessor supplies on motherboards, in VRMs and servers. The TDA21201 can also be used to power Logic circuits, Memory banks etc. that require higher voltages, e.g. 2.5 or 3.3 V. The efficiency of the Integrated Switch and the overall efficiency of the converter will even go up at these elevated output voltages compared to the 1.6 V efficiency given later on in this data sheet.
Page 4
Apr-29, 2002
Preliminary Data Sheet
TDA21201
Designing a 12 V to sub-3.3 V converter using the TDA21201 General info To design a multi-phase converter with a 12 V input simply use in each phase just one TDA21201 instead of using a MOSFET driver, a high side MOSFET, bootstrap components, and one or more low side MOSFETs. The entire converter is completed by the input filter, the output filter and a multi-phase PWM IC. Input compatibility to standard PWM controllers / shut-down mode The Integrated Switch TDA21201 has a high impedance input pin `IN' to be connected to PWM controller outputs `PWM1', `PWM2' etc. It sinks or sources only a fraction of a mA from the controller's output. The TDA21201 is compatible to standard controller and driver signals in terms of the signal level (5 V TTL) and in terms of the `Low'/'High' relationship ('Low' turns the low side MOSFET on, `High turns the High side MOSFET on). The TDA21201 can be shut down (the high side MOSFET and the low side MOSFET is turned off) by applying an input signal VIN = 1.2 ... 1.6 V for more than 1.5 s typical. This way the TDA21201 reduces the power dissipation by saving the gate charges of both the high side and the low side MOSFET during no load conditions. The shutdown state is terminated when VIN moves into the `Low' or `High' threshold. Typical Application: 12 V a 1.x V N-Phase Converter using the TDA21201 12 V
FET Driver 1 PWM 1
L1
1...2 V
C
PWM IC
PWM 2 PWM N LN
FET Driver N
Page 5
Apr-29, 2002
Preliminary Data Sheet
TDA21201
12 V VCC L1 IN
TDA 21201
OUT
1...2 V C
PWM 1
PWM IC
GND
PWM 2 PWM N
TDA 21201
LN
Integrated Switch functionality vs. supply voltage Vcc
Integrated Switch function
High Side FET can turn ON
Low Side FET can turn ON Integrated Switch OFF I 6V I 7.5 V I 9V Integrated Switch fully functional I 12 V I 15 V
Vcc
The Integrated Switch reaches gradually its full functionality while the supply voltage Vcc increases from 0 to its nominal value +12 V, e.g. during turn-on. The same happens vice versa when the supply voltage decreases from its nominal value +12 V to 0, e.g. during turn-off. The TDA21201 is very insensitive to Vcc tolerances. It behaves properly in a wide Vcc range from 9 to 15 V. There is no distinct VCC threshold at which the Integrated Switch's functionality or state changes abrupt while VCC increases or decreases. E.g., there is no tight specified Under Voltage Lockout level. The TDA21201 changes smoothly its state, e.g., as the High Side and Low Side MOSFETs gate drive voltage increases while VCC increases from 7.5 V to 9 V the Rds[on] of both the High Side MOSFET and the Low Side MOSFET decreases gradually, rather than being fully Off at VCC slightly below a threshold level or
Page 6 Apr-29, 2002
Preliminary Data Sheet being fully On at a VCC level slightly greater than the threshold.
TDA21201
Bootstrapping Turning on and off the High side MOSFET is done internally by the Driver. The TDA21201 does not require any external bootstrap components such as a capacitor or diode. Just apply GND, Vcc = 12 V, and the PWM signal of the Controller to it and the Integrated Switch will operate. Input filter / Output filter / Converter Stability The Integrated Switch TDA21201 is a new solution to implement the power semiconductor components in a DC/DC converter. It offers many advantages to the user. However, the basic behavior with respect to the voltages, the currents and the timing remains unchanged. Therefore, any of the rules and procedures applied to design DC/DC converters using discrete MOSFETs and Drivers apply in the same way to converters using the Integrated Switch - except the worries regarding dead time control, lowest impedance in the AC loop, elevated driver temperatures etc. Current sense Any of the commonly used current sense techniques are supported by the Integrated Switch. For Low side sensing measure the voltage drop across the GND pins and the OUT pin (or the tab when using the SMD version) during the Low side switch's On-time (Vin = Low). The High side MOSFET is sensed across the Vcc and the OUT pin (or the tab when using the SMD version) of the Integrated Switch during its On-time (Vin = High). Inductor sensing is implemented outside of the integrated switch the usual way. Resistor sensing using a separate resistor in the Input capacitor a High side MOSFET (Vcc pin) path is possible but not recommended. This current sense approach introduces ample stray inductance in the AC current loop (+terminal of the input capacitor a High side MOSFET a Low side MOSFET a GND a -terminal of the input capacitor). This results in a very noisy Vcc line especially during the switching period and a non-optimized switching behavior of the Integrated Switch. This in turn, increases the switching losses and the device temperature and lowers the efficiency. Output current scalability The converter output current can be chosen in a wide range by selecting the appropriate number of phases. At a given number of phases the current per phase (= current per TDA21201) and in turn the overall converter output current is set by application requirements, e.g. the switching frequency, and by environmental conditions, e.g. ambient temperature and the thermal resistance of the TDA21201 to ambient. As a reference, one TDA21201 generates roughly 3.2 W @ 15 A RMS and 250 kHz (VCC = 12 V, VO = 1.6 V). This amount of loss can be dissipated by the SMD version of the Integrated Switch on a regular motherboard using proper thermal design techniques. Greater phase currents result in higher losses; and higher switching
Page 7 Apr-29, 2002
Preliminary Data Sheet
TDA21201
frequencies will also result in more losses. So, in modifying the thermal environment and a switching frequency the phase current can be matched your requirements; please, consult the efficiency curves in this Data Sheet to choose the most suitable phase current and switching frequency per phase for a particular design. To give a circuit designer more freedom in scaling the phase current, the Integrated Switch is offered in a heat sink capable TO-220 version that allows better thermal coupling to ambient and a higher junction temperature in the Integrated Switch as well - without violating the applicable regulations. Over temperature shut-down The over temperature shut-down function of the Integrated Switch takes effect @ 150 C junction temperature typically and turns off the High side MOSFET and the Low side MOSFET. Unlike as in discrete converter solutions the MOSFETs and the Driver are thermally very well coupled. Therefore, this function protects the Driver and the MOSFETs. Once the Integrated Switch is cooled down and the temperature shut-down is released the Integrated Switch continues to operate by turning on one of the MOSFETs according to its PWM signal present on the input. Under Voltage Lockout / Vcc detection The TDA21201 is fully functional at Vcc 9 V. However, the Low side MOSFET can already be turned on at Vcc 6 V or greater when the input is Low. The Integrated Switch is disabled and both MOSFETs are turned off at lower Vcc, e.g. during power-up of the ATX supply. The TDA21201 has two paralleled Vcc pins. The voltage applied to these pins will be converted to a lower output voltage but it also serves as supply voltage of the integrated gate drive circuit. Therefore, the voltage difference Vcc is monitored for safety reasons. When Vcc 0.45 V for more than 2 s typically the Integrated Switch is disabled. This way it prevents the part itself but it also protects the load from inadequate behavior, e.g. due to a bad soldering connection of the Vcc pins. Layout guidelines In general, the layout is simplified when using the Integrated Switch. However, it should be kept in mind that the power density in the Integrated Switch is higher than in a discrete solution. Therefore, proper thermal layout is very critical in designs that employ the SMD version. Another important aspect is a very low impedance path in the Vcc = 12 V a TDA21201 a GND loop. It is recommended to place the capacitors of the input filter as close to the GND and Vcc pins of the TDA21201 as possible. Additional ceramic capacitors in parallel to the input capacitors help to reduce the effect of stray inductance of the input capacitors and the PCB traces. Reducing parasitic inductance will result in an optimized switching behavior and lower switching losses. The arrangement of the output filter is of second order importance.
Page 8 Apr-29, 2002
Preliminary Data Sheet
TDA21201
Over voltage protection of Vcc / Avalanche avoidance The voltage at the Vcc pins of the TDA21201 rises above the nominal DC value of the Vcc supply (= + 12 V) during the turn-off of the High Side MOSFET. The voltage overshoots at the Vcc pins according to: vcc(t) = Vcc + Lstray * di/dt vcc (t) = instantaneous value of vcc; Vcc = +12 V DC; Lstray = stray inductance of the PCB traces + the input capacitor's ESL + the parasitic inductance of the TDA21201 package itself; di/dt = slew rate of the High Side current during its turn-off. Vcc = +12 V TDA21201 Lstray
HS is turned off
V < 20
vcc
t
Dz
HS
Cin Lout
Driver LS
This equation reveals that Lstray should be made as small as possible (as vcc(t) is limited by the breakdown voltage of the device, Vcc is given by the application, di/dt should be as large as possible to reduce switching losses) using proper layout techniques and low ESL capacitors, e.g. ceramics, between the Vcc and GND pins of the Integrated Switch. To protect the Integrated Switch from unallowable voltage spikes, the slew rate of the High Side current di/dt is controlled in a way so that the overall voltage (between Vcc pins to GND pins) does not exceed 20 V (measured between the Vcc and GND pins at the PCB, this voltage will slightly exceed the 20 V limit within the package/at the chips). As the MOSFETs have a Breakdown voltage rating Vds = 30 V, it is made sure that they are never driven into avalanche. The slew rate control is implemented using the principal of the active zener clamp technique: When vcc(t) rises during turn-off then the effective gate-drain voltage of the High Side MOSFET rises, too. If, for what reason ever, the vcc(t) overshoot approaches a value that possibly could damage the integrated
Page 9 Apr-29, 2002
Preliminary Data Sheet
TDA21201
driver or the MOSFETs, the zener diode becomes conducting and reduces the discharge speed of the High Side MOSFETs gate within nanoseconds. This will reduce slightly the turn-off slew rate of the High Side MOSFETs current (= di/dt). As a result the over voltage will be limited. Power loss in the Integrated Switch TDA21201 / Heat sink estimation The power loss in the Integrated Switch depends mainly on the current and the switching frequency. Other conditions that impact the power loss are increased junction temperature and the layout (e.g. very tight coupling of the input capacitor to the VCC and GND pins to reduce the PCB trace inductance).
6 Iphase =12 A 5 Pd [W] 4 3 2 1 100 150 200 250 300 350 400 450 Iphase =18 A
f_sw / phase [kHz]
6 f_sw = 100 kHz 5 Pd [W] 4 3 2 1 10 15 Iphase [A] 20 25 f_sw = 150 kHz f_sw = 200 kHz f_sw = 250 kHz f_sw = 300 kHz
Using the above two diagrams the power loss (= the required power dissipation Pd for thermally stable operation) can be estimated based on a required phase current Iphase (= current in the Integrated Switch) an based on the switching frequency per phase f_sw (= frequency of the Integrated Switch in each phase).
Page 10
Apr-29, 2002
Preliminary Data Sheet
TDA21201
Having the power dissipation Pd of the Integrated Switch, the required thermal resistance RthCA can be calculated. RthCA is the value of the heat sink attached to the TO-220 version of the Integrated Switch. RthCA is the "effective" thermal resistance (takes airflow etc. into account):
RthCA Tj _ max - TA - Rthjc Pd
Wherein:
RthCA = Thermal resistance from the package's metal backside (= lead frame) to ambient air that is required to operate the Integrated Switch under given load and environmental conditions without exceeding the maximum allowed junction temperature; in [C/W] Tj_max = Maximum allowed junction temperature of the Integrated Switch; in [C], use 110 C for the SMD version of the Integrated Switch, use 125 C for the TO-220 version of the Integrated Switch TA = The ambient temperature; in [C], usually this is the maximum temperature of the surrounding air @ worst case, e.g. 55 C Pd = The power loss generated in the Integrated Switch that needs to be dissipated through the heat sink a air (TO-220) or the PCB a air for thermal balance; in [W], use one of the two diagrams Pd vs. Iphase or Pd vs. f_sw to find the this value for your particular application Rthjc = Thermal resistance junction to case of the Integrated Switch; in [K/W], use 2 K/W (s. also pg. 3 and 4 "Thermal characteristic of the High side/Low side MOSFET" in this data sheet; the majority of the losses are generated within the MOSFETs, not in the driver)
Efficiency of a DC/DC converter using the Integrated Switch TDA21201 The following measurements were performed on a 4-phase Evaluation Board. Phase 4 can be disabled so that the converter operates in a 3-phase mode. Boundary Conditions: Vcc = 12 V, Vo = 1.6 V, TDA21201 as SMD I 4-Phase Converter: Efficiency vs. Load current
95 90
Efficiency [%]
85 80 75 70 65 0 20 40
Load Current [A]
f_1 = 185 kHz f_2 = 305 kHz
60
80
Page 11
Apr-29, 2002
Preliminary Data Sheet II 4-Phase Converter: Efficiency vs. Switching frequency
95 Efficiency [%] 90
Io_1 = 25 A
TDA21201
85 80 75
150 200 250 300 350
Io_2 = 40 A Io_3 = 55 A Io_4 = 70 A
Frequency / Phase [kHz]
Ill 3- and 4-Phase Converter: Efficiency vs. Load current
95 90 Efficiency [%] 85
4 Phase @ 185 kHz
80
4 Phase @ 305 kHz
75 70 65 0 10 20 30 Load current [A] 40 50 60
3 Phase @ 185 kHz 3 Phase @ 305 kHz
It should be noted that the overall converter efficiency and the maximum converter output power will increase as the output voltage increases, e.g. VO = 2.5 or 3.3 V.
Page 12
Apr-29, 2002
Preliminary Data Sheet Package Drawing TO-220-7-3 (straight leads)
TDA21201
Package Drawing TO-220-7-230 (staggered leads)
Page 13
Apr-29, 2002
Preliminary Data Sheet Package Drawing TO-263-7-2 (SMD)
TDA21201
Page 14
Apr-29, 2002
Preliminary Data Sheet
Published by Infineon Technologies AG, Bereichs Kommunikation St.-Martin-Strasse 53, D-81541 Munchen (c) Infineon Technologies AG 1999 All Rights Reserved.
TDA21201
Attention please! The information herein is given to describe certain components and shall not be considered as warranted Characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office in Germany or our Infineon Technologies Representatives worldwide (see address lists). Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
Page 15
Apr-29, 2002

▲Up To Search▲

Price & Availability of TDA21201

	To Download TDA21201 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .